Timken X2S462 X2S 462 Spacer Retainer Bearing

H1:114.3 mm; P180°:42.7 kN; Cap bolt:2 x 3/4-10 UNC; Bearing:22317 EK; End plug (suffix Y):EPR 10; H:222.25 mm; Mass pillow block:34 kg; N1:22.225 mm; RG:3/8 NPT; P120°:39.1 kN;

H1:114.3 mm; P180°:42.7 kN; Cap bolt:2 x 3/4-10 UNC; Bearing:22317 EK; End plug (suffix Y):EPR 10; H:222.25 mm; Mass pillow block:34 kg; N1:22.225 mm; RG:3/8 NPT; P120°:39.1 kN;

Grease Speed Rating n1:11000 rpm; Oil Speed Rating n2:14000 rpm; B:17.00 mm; Fillet Radius ra:1.00 mm; Sealed Speed Rating n3:7500 rpm; d:25.000 mm; Basic Dynamic Radial Load Rating C:21200 N; Accessories:One Seal; Basic Static Radial Load Rating Co:10800 N; Grease Speed Rating Open/Shielded n1:11000 rpm;

r3,4 min.:2.5 mm; Calculation factor Y:1.4; Basic dynamic load rating C:304 kN; Limiting speed:3600 r/min; D:180 mm; Da min.:157 mm; Db min.:168 mm; Ca min.:5 mm; d:100 mm; ra max.:3 mm;

P120°:13.3 kN; H1:82.55 mm; N1:15.875 mm; Cap bolt recommended tightening torque:149.1 N·m; J1:50.8 mm; L:279.4 mm; Pa:6.94 kN; Labyrinth ring:2 x LER 25; H:157.162 mm; A2:123.825 mm;

Calculation factor kr:0.2; da min.:70 mm; Basic dynamic load rating C:58.3 kN; Mass bearing:0.31 kg; Da max.:85 mm; das:73.4 mm; d1 ≈:75.5 mm; D:90 mm; D1 ≈:81 mm; Db max.:86 mm;

P120°:13.3 kN; H1:82.55 mm; N1:15.875 mm; Cap bolt recommended tightening torque:149.1 N·m; J1:50.8 mm; L:279.4 mm; Pa:6.94 kN; Labyrinth ring:2 x LER 25; H:157.162 mm; A2:123.825 mm;

d:45 mm; d1 ≈:52 mm; C:25 mm; b1:4.6 mm; Specific dynamic load factor K:150 N/mm²; Specific static load factor K0:500 N/mm²; Mass plain bearing:0.49 kg; Material constant KM:330; Da max.:63.6 mm; B:40 mm;

J1:85.725 mm; H2:60.325 mm; Initial grease fill:481.95 g; P150°:85.9 kN; End plug (suffix Y):EPR 18; Eye bolt:3/8-16 UNC; P90°:149 kN; N1:28.575 mm; J min.:396.875 mm; Cap bolt recommended tightening torque:400 N·m;

H1:114.3 mm; P180°:42.7 kN; Cap bolt:2 x 3/4-10 UNC; Bearing:22317 EK; End plug (suffix Y):EPR 10; H:222.25 mm; Mass pillow block:34 kg; N1:22.225 mm; RG:3/8 NPT; P120°:39.1 kN;

J1:85.725 mm; H2:60.325 mm; Initial grease fill:481.95 g; P150°:85.9 kN; End plug (suffix Y):EPR 18; Eye bolt:3/8-16 UNC; P90°:149 kN; N1:28.575 mm; J min.:396.875 mm; Cap bolt recommended tightening torque:400 N·m;

d2 ≈:510 mm; ra max.:5 mm; Limiting speed:670 r/min; s1 max.:27.8 mm; D:720 mm; Da max.:694 mm; Basic static load rating C0:12900 kN; Fatigue load limit Pu:900 kN; Basic dynamic load rating C:7500 kN; B:280 mm;

H1:114.3 mm; P180°:42.7 kN; Cap bolt:2 x 3/4-10 UNC; Bearing:22317 EK; End plug (suffix Y):EPR 10; H:222.25 mm; Mass pillow block:34 kg; N1:22.225 mm; RG:3/8 NPT; P120°:39.1 kN;