N217 Cylindrical roller bearings

J6:285 mm; Recommended diameter for attachment bolts, inch G:0.75 in; J max.:241 mm; Bearing:YAR 216-300-2F; Rα:45 °; A:78 mm; s1:47.6 mm; N:38 mm; Thread grub screw G2:7/16-20 UNF; N4:3 mm;

End plug (suffix Y):EPR 9; Cap bolt, SAE grade:8; db:92.075 mm; Stabilizing ring:SR-16-13; Max. speed for Taconite seal:850 r/min; R2:21.431 mm; P120°:49.8 kN; ba:34.131 mm; da:80 mm; Cap bolt:2 x 5/8-11 UNC;

PG:1/4 NPT; H:222.25 mm; da:107.95 mm; H1:114.3 mm; Stabilizing ring:2 x 38151-24; P60°:175 kN; J min.:295.275 mm; Cap bolt, SAE grade:8; J1:60.325 mm; H2:44.45 mm;

PG:1/4 NPT; H:222.25 mm; da:107.95 mm; H1:114.3 mm; Stabilizing ring:2 x 38151-24; P60°:175 kN; J min.:295.275 mm; Cap bolt, SAE grade:8; J1:60.325 mm; H2:44.45 mm;

Fatigue load limit Pu:90 kN; Basic static load rating C0:7650 kN; Basic dynamic load rating C:630 kN; da min.:991 mm; Reference speed:360 r/min; d1 ≈:1054 mm; Mass bearing (including seat washer where applicable):140 kg; r1,2 min.:5 mm; d:900 mm; H:95 mm;

J6:285 mm; Recommended diameter for attachment bolts, inch G:0.75 in; J max.:241 mm; Bearing:YAR 216-300-2F; Rα:45 °; A:78 mm; s1:47.6 mm; N:38 mm; Thread grub screw G2:7/16-20 UNF; N4:3 mm;

Limiting speed:14000 r/min; db min.:61 mm; Mass bearing:0.55 kg; da max.:57.5 mm; Reference speed:8500 r/min; Angle ring:HJ 210 EC; F:59.5 mm; Limiting value e:0.2; D1 ≈:77.95 mm; Calculation factor kr:0.23;

R1:122.237 mm; ba:89.694 mm; Taconite seal:TER 513; A1:203.2 mm; Max. speed for Taconite seal:340 r/min; N1:34.925 mm; P90°:218 kN; Cap bolt:4 x 7/8-9 UNC; Initial grease fill:2154.6 g; J1:127 mm;

PG:1/4 NPT; H:222.25 mm; da:107.95 mm; H1:114.3 mm; Stabilizing ring:2 x 38151-24; P60°:175 kN; J min.:295.275 mm; Cap bolt, SAE grade:8; J1:60.325 mm; H2:44.45 mm;

d:300 mm; Mass bearing:70 kg; d2 ≈:351 mm; D1 ≈:417 mm; Limiting speed:1500 r/min; s1 max.:20 mm; ra max.:3 mm; B:118 mm; Basic dynamic load rating C:2160 kN; Da min.:402 mm;

B:20 mm; rs (min):1 mm; T:20 mm; Dynamic (Ca):59.6 kN; a:18 mm; r1s (min):1 mm; d2:50 mm; r2s (min):0.3 mm; C:15.5 mm; Static (Coa):87.4 kN;

D:240.0000 mm; Basic Static Radial Load Rating Co:305000 N; Oil Speed Rating n2:2400 rpm; Accessories:Two Seals; Fillet Radius ra:2.50 mm; B:92.10 mm; Basic Dynamic Radial Load Rating C:291000 N; Sealed Speed Rating n3:1700 rpm; Grease Speed Rating n1:1700 rpm; d:110.000 mm;

Fatigue load limit Pu:90 kN; Basic static load rating C0:7650 kN; Basic dynamic load rating C:630 kN; da min.:991 mm; Reference speed:360 r/min; d1 ≈:1054 mm; Mass bearing (including seat washer where applicable):140 kg; r1,2 min.:5 mm; d:900 mm; H:95 mm;

Fatigue load limit Pu:6 kN; U:20 mm; Designation associated SD design radial shaft seal with a low cross-sectional height:SD 35x42x4; Designation associated G design radial shaft seal with a low cross-sectional height:G 35x42x4; Basic dynamic load rating C:29.2 kN; Basic static load rating C0:50 kN; Ew:42 mm; Limiting speed:13000 r/min; Reference speed:11000 r/min; Mass needle roller and cage assembly:0.037 kg;

R1:122.237 mm; ba:89.694 mm; Taconite seal:TER 513; A1:203.2 mm; Max. speed for Taconite seal:340 r/min; N1:34.925 mm; P90°:218 kN; Cap bolt:4 x 7/8-9 UNC; Initial grease fill:2154.6 g; J1:127 mm;