Thin Section Bearings Kaydon SB075AH4

Basic Static Radial Load Rating Co:186000 N; Grease Speed Rating n1:2800 rpm; Accessories:Two Seals & Snap-Rin; d:70.000 mm; B:63.50 mm; Oil Speed Rating n2:3800 rpm; D:150.0000 mm; Sealed Speed Rating n3:2800 rpm; Fillet Radius ra:2.00 mm; Basic Dynamic Radial Load Rating C:172000 N;

P120°:66.7 kN; RG:3/8 NPT; Initial grease fill:232.47 g; P90°:107 kN; L:419.1 mm; H1:125.425 mm; H2:52.388 mm; Cap bolt recommended tightening torque:298.3 N·m; Housing:SSAFS 026 KA; A2:231.775 mm;

L:749.3 mm; Appropriate attachment bolt size G:1.25 in; Cap bolt:4 x 7/8-9 UNC; da:150.813 mm; Taconite seal:TER 140; P120°:136 kN; H:422.275 mm; Initial grease fill:2154.6 g; Cap bolt, SAE grade:5; J max.:635 mm;

d:140 mm; B4:27 mm; Lock nut:AN 28; d1:122.237 mm; Hydraulic nut:HMVC 28E; Threads per inch:12; B1:134.95 mm; G:139.624 mm; B:24.079 mm; d3 max.:180.315 mm;

L:749.3 mm; Appropriate attachment bolt size G:1.25 in; Cap bolt:4 x 7/8-9 UNC; da:150.813 mm; Taconite seal:TER 140; P120°:136 kN; H:422.275 mm; Initial grease fill:2154.6 g; Cap bolt, SAE grade:5; J max.:635 mm;

Calculation factor Y0:2; d1 ≈:534 mm; r3,4 min.:1.5 mm; Comparative axial load rating CFa:358 kN; T:446.088 mm; D:635 mm; Basic static load rating C0:22000 kN; Thrust factor K:1.76; Mass bearing:475 kg; Fatigue load limit Pu:1600 kN;

Basic static load rating C0:33.5 kN; Reference speed:13000 r/min; Ew:37 mm; Limiting speed:15000 r/min; U:16 mm; Fw:30 mm; Mass needle roller and cage assembly:0.027 kg; Fatigue load limit Pu:4 kN; Designation associated G design radial shaft seal with a low cross-sectional height:G 30x37x4; Designation associated SD design radial shaft seal with a low cross-sectional height:SD 30x37x4;

D:12 mm; Mass bushing:0.0066 kg; Tolerance shaft:e7; Coefficient of friction µ min.:0.08; Permissible sliding velocity v max.:0.5 m/s; B:10 mm; d:7 mm; Permissible sliding velocity v min.:0 m/s; Tolerance housing:H7; Coefficient of friction µ max.:0.15;

d:90.000 mm; Grease Speed Rating Open/Shielded n1:3400 rpm; Accessories:Two Shields; Grease Speed Rating n1:3400 rpm; Basic Static Radial Load Rating Co:108000 N; Fillet Radius ra:2.50 mm; Oil Speed Rating n2:4000 rpm; B:43.00 mm; Oil Speed Rating Open/Shielded n2:4000 rpm; D:190.0000 mm;

D:190.0000 mm; Basic Dynamic Radial Load Rating C:157000 N; Oil Speed Rating Open/Shielded n2:3400 rpm; B:43.00 mm; Grease Speed Rating Open/Shielded n1:2800 rpm; Basic Static Radial Load Rating Co:160000 N; Fillet Radius ra:2.50 mm; d:90.000 mm; Accessories:Without Accessories;

h:46.038 mm; A1:120.65 mm; R2:30.163 mm; da:125.412 mm; Pa:22.2 kN; Stabilizing ring:2 x 36053-50; H:257.175 mm; P150°:87.2 kN; Ca:72.619 mm; Initial grease fill:379.89 g;

D:12 mm; Mass bushing:0.0066 kg; Tolerance shaft:e7; Coefficient of friction µ min.:0.08; Permissible sliding velocity v max.:0.5 m/s; B:10 mm; d:7 mm; Permissible sliding velocity v min.:0 m/s; Tolerance housing:H7; Coefficient of friction µ max.:0.15;

L:749.3 mm; Appropriate attachment bolt size G:1.25 in; Cap bolt:4 x 7/8-9 UNC; da:150.813 mm; Taconite seal:TER 140; P120°:136 kN; H:422.275 mm; Initial grease fill:2154.6 g; Cap bolt, SAE grade:5; J max.:635 mm;

D:12 mm; Mass bushing:0.0066 kg; Tolerance shaft:e7; Coefficient of friction µ min.:0.08; Permissible sliding velocity v max.:0.5 m/s; B:10 mm; d:7 mm; Permissible sliding velocity v min.:0 m/s; Tolerance housing:H7; Coefficient of friction µ max.:0.15;

dk:105 mm; B:55 mm; l8:5 mm; l7 min.:98 mm; Specific dynamic load factor K:100 N/mm²; l6 max.:237 mm; d6:6 mm; h2:141 mm; d2 max.:182 mm; α:6 °;