Thin Section Bearings Timken C76-92MC7

Calculation factor Y0:2; d1 ≈:534 mm; r3,4 min.:1.5 mm; Comparative axial load rating CFa:358 kN; T:446.088 mm; D:635 mm; Basic static load rating C0:22000 kN; Thrust factor K:1.76; Mass bearing:475 kg; Fatigue load limit Pu:1600 kN;

Basic Static Radial Load Rating Co:186000 N; Grease Speed Rating n1:2800 rpm; Accessories:Two Seals & Snap-Rin; d:70.000 mm; B:63.50 mm; Oil Speed Rating n2:3800 rpm; D:150.0000 mm; Sealed Speed Rating n3:2800 rpm; Fillet Radius ra:2.00 mm; Basic Dynamic Radial Load Rating C:172000 N;

a:3 mm; D:40 mm; B:25 mm; Coefficient of friction µ max.:0.15; Specific static load factor K0:45 N/mm²; Mass bushing:0.14 kg; h:29 mm; Tolerance housing:H7; Permissible sliding velocity v min.:0 m/s; α:124 °;

Basic Static Radial Load Rating Co:186000 N; Grease Speed Rating n1:2800 rpm; Accessories:Two Seals & Snap-Rin; d:70.000 mm; B:63.50 mm; Oil Speed Rating n2:3800 rpm; D:150.0000 mm; Sealed Speed Rating n3:2800 rpm; Fillet Radius ra:2.00 mm; Basic Dynamic Radial Load Rating C:172000 N;

D:190.0000 mm; Basic Dynamic Radial Load Rating C:157000 N; Oil Speed Rating Open/Shielded n2:3400 rpm; B:43.00 mm; Grease Speed Rating Open/Shielded n1:2800 rpm; Basic Static Radial Load Rating Co:160000 N; Fillet Radius ra:2.50 mm; d:90.000 mm; Accessories:Without Accessories;

h:46.038 mm; A1:120.65 mm; R2:30.163 mm; da:125.412 mm; Pa:22.2 kN; Stabilizing ring:2 x 36053-50; H:257.175 mm; P150°:87.2 kN; Ca:72.619 mm; Initial grease fill:379.89 g;

Basic static load rating C0:33.5 kN; Reference speed:13000 r/min; Ew:37 mm; Limiting speed:15000 r/min; U:16 mm; Fw:30 mm; Mass needle roller and cage assembly:0.027 kg; Fatigue load limit Pu:4 kN; Designation associated G design radial shaft seal with a low cross-sectional height:G 30x37x4; Designation associated SD design radial shaft seal with a low cross-sectional height:SD 30x37x4;

h:46.038 mm; A1:120.65 mm; R2:30.163 mm; da:125.412 mm; Pa:22.2 kN; Stabilizing ring:2 x 36053-50; H:257.175 mm; P150°:87.2 kN; Ca:72.619 mm; Initial grease fill:379.89 g;

a:3 mm; D:40 mm; B:25 mm; Coefficient of friction µ max.:0.15; Specific static load factor K0:45 N/mm²; Mass bushing:0.14 kg; h:29 mm; Tolerance housing:H7; Permissible sliding velocity v min.:0 m/s; α:124 °;

P120°:107 kN; Bearing:23238 CCK/W33; ba:92.869 mm; P90°:173 kN; Da:339.999 mm; H2:79.375 mm; Initial grease fill:1672.65 g; L:711.2 mm; Cap bolt:4 x 7/8-9 UNC; Adapter sleeve assembly:SNW 138x6.7/8;

a:3 mm; D:40 mm; B:25 mm; Coefficient of friction µ max.:0.15; Specific static load factor K0:45 N/mm²; Mass bushing:0.14 kg; h:29 mm; Tolerance housing:H7; Permissible sliding velocity v min.:0 m/s; α:124 °;

Basic static load rating C0:33.5 kN; Reference speed:13000 r/min; Ew:37 mm; Limiting speed:15000 r/min; U:16 mm; Fw:30 mm; Mass needle roller and cage assembly:0.027 kg; Fatigue load limit Pu:4 kN; Designation associated G design radial shaft seal with a low cross-sectional height:G 30x37x4; Designation associated SD design radial shaft seal with a low cross-sectional height:SD 30x37x4;

D:190.0000 mm; Basic Dynamic Radial Load Rating C:157000 N; Oil Speed Rating Open/Shielded n2:3400 rpm; B:43.00 mm; Grease Speed Rating Open/Shielded n1:2800 rpm; Basic Static Radial Load Rating Co:160000 N; Fillet Radius ra:2.50 mm; d:90.000 mm; Accessories:Without Accessories;

a:3 mm; D:40 mm; B:25 mm; Coefficient of friction µ max.:0.15; Specific static load factor K0:45 N/mm²; Mass bushing:0.14 kg; h:29 mm; Tolerance housing:H7; Permissible sliding velocity v min.:0 m/s; α:124 °;

L:749.3 mm; Appropriate attachment bolt size G:1.25 in; Cap bolt:4 x 7/8-9 UNC; da:150.813 mm; Taconite seal:TER 140; P120°:136 kN; H:422.275 mm; Initial grease fill:2154.6 g; Cap bolt, SAE grade:5; J max.:635 mm;