Thin Section Bearings Timken S76-86MC5

d:140 mm; B4:27 mm; Lock nut:AN 28; d1:122.237 mm; Hydraulic nut:HMVC 28E; Threads per inch:12; B1:134.95 mm; G:139.624 mm; B:24.079 mm; d3 max.:180.315 mm;

P120°:66.7 kN; RG:3/8 NPT; Initial grease fill:232.47 g; P90°:107 kN; L:419.1 mm; H1:125.425 mm; H2:52.388 mm; Cap bolt recommended tightening torque:298.3 N·m; Housing:SSAFS 026 KA; A2:231.775 mm;

P120°:66.7 kN; RG:3/8 NPT; Initial grease fill:232.47 g; P90°:107 kN; L:419.1 mm; H1:125.425 mm; H2:52.388 mm; Cap bolt recommended tightening torque:298.3 N·m; Housing:SSAFS 026 KA; A2:231.775 mm;

D:12 mm; Mass bushing:0.0066 kg; Tolerance shaft:e7; Coefficient of friction µ min.:0.08; Permissible sliding velocity v max.:0.5 m/s; B:10 mm; d:7 mm; Permissible sliding velocity v min.:0 m/s; Tolerance housing:H7; Coefficient of friction µ max.:0.15;

a:3 mm; D:40 mm; B:25 mm; Coefficient of friction µ max.:0.15; Specific static load factor K0:45 N/mm²; Mass bushing:0.14 kg; h:29 mm; Tolerance housing:H7; Permissible sliding velocity v min.:0 m/s; α:124 °;

d:90.000 mm; Grease Speed Rating Open/Shielded n1:3400 rpm; Accessories:Two Shields; Grease Speed Rating n1:3400 rpm; Basic Static Radial Load Rating Co:108000 N; Fillet Radius ra:2.50 mm; Oil Speed Rating n2:4000 rpm; B:43.00 mm; Oil Speed Rating Open/Shielded n2:4000 rpm; D:190.0000 mm;

D:190.0000 mm; Basic Dynamic Radial Load Rating C:157000 N; Oil Speed Rating Open/Shielded n2:3400 rpm; B:43.00 mm; Grease Speed Rating Open/Shielded n1:2800 rpm; Basic Static Radial Load Rating Co:160000 N; Fillet Radius ra:2.50 mm; d:90.000 mm; Accessories:Without Accessories;

D:12 mm; Mass bushing:0.0066 kg; Tolerance shaft:e7; Coefficient of friction µ min.:0.08; Permissible sliding velocity v max.:0.5 m/s; B:10 mm; d:7 mm; Permissible sliding velocity v min.:0 m/s; Tolerance housing:H7; Coefficient of friction µ max.:0.15;

Basic Static Radial Load Rating Co:186000 N; Grease Speed Rating n1:2800 rpm; Accessories:Two Seals & Snap-Rin; d:70.000 mm; B:63.50 mm; Oil Speed Rating n2:3800 rpm; D:150.0000 mm; Sealed Speed Rating n3:2800 rpm; Fillet Radius ra:2.00 mm; Basic Dynamic Radial Load Rating C:172000 N;

Basic Static Radial Load Rating Co:186000 N; Grease Speed Rating n1:2800 rpm; Accessories:Two Seals & Snap-Rin; d:70.000 mm; B:63.50 mm; Oil Speed Rating n2:3800 rpm; D:150.0000 mm; Sealed Speed Rating n3:2800 rpm; Fillet Radius ra:2.00 mm; Basic Dynamic Radial Load Rating C:172000 N;

h:46.038 mm; A1:120.65 mm; R2:30.163 mm; da:125.412 mm; Pa:22.2 kN; Stabilizing ring:2 x 36053-50; H:257.175 mm; P150°:87.2 kN; Ca:72.619 mm; Initial grease fill:379.89 g;

d:60.000 mm; Oil Speed Rating n2:4500 rpm; Accessories:No Shield, no Seal; B:54.00 mm; Grease Speed Rating n1:3400 rpm; Basic Static Radial Load Rating Co:143000 N; Sealed Speed Rating n3:3400 rpm; Fillet Radius ra:2.00 mm; Basic Dynamic Radial Load Rating C:134000 N; D:130.0000 mm;

Calculation factor Y0:2; d1 ≈:534 mm; r3,4 min.:1.5 mm; Comparative axial load rating CFa:358 kN; T:446.088 mm; D:635 mm; Basic static load rating C0:22000 kN; Thrust factor K:1.76; Mass bearing:475 kg; Fatigue load limit Pu:1600 kN;

D:190.0000 mm; Basic Dynamic Radial Load Rating C:157000 N; Oil Speed Rating Open/Shielded n2:3400 rpm; B:43.00 mm; Grease Speed Rating Open/Shielded n1:2800 rpm; Basic Static Radial Load Rating Co:160000 N; Fillet Radius ra:2.50 mm; d:90.000 mm; Accessories:Without Accessories;

d:140 mm; B4:27 mm; Lock nut:AN 28; d1:122.237 mm; Hydraulic nut:HMVC 28E; Threads per inch:12; B1:134.95 mm; G:139.624 mm; B:24.079 mm; d3 max.:180.315 mm;