Thin Section Bearings Timken S144-168MC5

h:46.038 mm; A1:120.65 mm; R2:30.163 mm; da:125.412 mm; Pa:22.2 kN; Stabilizing ring:2 x 36053-50; H:257.175 mm; P150°:87.2 kN; Ca:72.619 mm; Initial grease fill:379.89 g;

D:12 mm; Mass bushing:0.0066 kg; Tolerance shaft:e7; Coefficient of friction µ min.:0.08; Permissible sliding velocity v max.:0.5 m/s; B:10 mm; d:7 mm; Permissible sliding velocity v min.:0 m/s; Tolerance housing:H7; Coefficient of friction µ max.:0.15;

L:749.3 mm; Appropriate attachment bolt size G:1.25 in; Cap bolt:4 x 7/8-9 UNC; da:150.813 mm; Taconite seal:TER 140; P120°:136 kN; H:422.275 mm; Initial grease fill:2154.6 g; Cap bolt, SAE grade:5; J max.:635 mm;

D:12 mm; Mass bushing:0.0066 kg; Tolerance shaft:e7; Coefficient of friction µ min.:0.08; Permissible sliding velocity v max.:0.5 m/s; B:10 mm; d:7 mm; Permissible sliding velocity v min.:0 m/s; Tolerance housing:H7; Coefficient of friction µ max.:0.15;

Accessories:One Seal & Snap-Ring; Oil Speed Rating n2:11000 rpm; Basic Static Radial Load Rating Co:14000 N; d:25.000 mm; Sealed Speed Rating n3:8000 rpm; Fillet Radius ra:1.00 mm; B:20.60 mm; Grease Speed Rating n1:8000 rpm; Basic Dynamic Radial Load Rating C:20800 N; D:52.0000 mm;

L:749.3 mm; Appropriate attachment bolt size G:1.25 in; Cap bolt:4 x 7/8-9 UNC; da:150.813 mm; Taconite seal:TER 140; P120°:136 kN; H:422.275 mm; Initial grease fill:2154.6 g; Cap bolt, SAE grade:5; J max.:635 mm;

L:749.3 mm; Appropriate attachment bolt size G:1.25 in; Cap bolt:4 x 7/8-9 UNC; da:150.813 mm; Taconite seal:TER 140; P120°:136 kN; H:422.275 mm; Initial grease fill:2154.6 g; Cap bolt, SAE grade:5; J max.:635 mm;

D:12 mm; Mass bushing:0.0066 kg; Tolerance shaft:e7; Coefficient of friction µ min.:0.08; Permissible sliding velocity v max.:0.5 m/s; B:10 mm; d:7 mm; Permissible sliding velocity v min.:0 m/s; Tolerance housing:H7; Coefficient of friction µ max.:0.15;

P120°:107 kN; Bearing:23238 CCK/W33; ba:92.869 mm; P90°:173 kN; Da:339.999 mm; H2:79.375 mm; Initial grease fill:1672.65 g; L:711.2 mm; Cap bolt:4 x 7/8-9 UNC; Adapter sleeve assembly:SNW 138x6.7/8;

h:46.038 mm; A1:120.65 mm; R2:30.163 mm; da:125.412 mm; Pa:22.2 kN; Stabilizing ring:2 x 36053-50; H:257.175 mm; P150°:87.2 kN; Ca:72.619 mm; Initial grease fill:379.89 g;

D:12 mm; Mass bushing:0.0066 kg; Tolerance shaft:e7; Coefficient of friction µ min.:0.08; Permissible sliding velocity v max.:0.5 m/s; B:10 mm; d:7 mm; Permissible sliding velocity v min.:0 m/s; Tolerance housing:H7; Coefficient of friction µ max.:0.15;

D:12 mm; Mass bushing:0.0066 kg; Tolerance shaft:e7; Coefficient of friction µ min.:0.08; Permissible sliding velocity v max.:0.5 m/s; B:10 mm; d:7 mm; Permissible sliding velocity v min.:0 m/s; Tolerance housing:H7; Coefficient of friction µ max.:0.15;

dk:105 mm; B:55 mm; l8:5 mm; l7 min.:98 mm; Specific dynamic load factor K:100 N/mm²; l6 max.:237 mm; d6:6 mm; h2:141 mm; d2 max.:182 mm; α:6 °;

Basic Static Radial Load Rating Co:186000 N; Grease Speed Rating n1:2800 rpm; Accessories:Two Seals & Snap-Rin; d:70.000 mm; B:63.50 mm; Oil Speed Rating n2:3800 rpm; D:150.0000 mm; Sealed Speed Rating n3:2800 rpm; Fillet Radius ra:2.00 mm; Basic Dynamic Radial Load Rating C:172000 N;

D:12 mm; Mass bushing:0.0066 kg; Tolerance shaft:e7; Coefficient of friction µ min.:0.08; Permissible sliding velocity v max.:0.5 m/s; B:10 mm; d:7 mm; Permissible sliding velocity v min.:0 m/s; Tolerance housing:H7; Coefficient of friction µ max.:0.15;